Buy Now — $2.96
Save money and time when building your own creations by using our simple-to-assemble motor mount kits. You'll save time because there is no cutting tubes to the correct lengths, nor do you have to search high-and-low to find all the correct size centering rings. Everything is already included in these motor mount kits. Most importantly, you'll save money because you don't need to buy a large quantity of tubes and rings just to make one or two motor mounts for your rockets. The convenience is worth...

Grasshopper — $5.24
Pencil. Ruler. Scissors. Plastic cement. Hobby Knife. Wood Glue or White Glue. Finishing Supplies like sanding sealer, paint and sandpaper (200 and 400 grit).

Daddy Long Legs — $14.62
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or White Glue. Finishing Supplies like sanding sealer, paint and sandpaper (200 and 400 grit).

INVADER — $29.95
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or White Glue.

Dynamo — $13.59
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or White Glue.

Copperhead" — $5.89
To use the copperhead, you must insulate one side of each microclip by using a piece of tape on the jaw. Then just attach the clips to the tail of the igniter, with the insulated sides of the clips on opposite sides of the igniter. At this point, you'll have continuity and you can fire off the igniter. I recommend a 12V car battery to set these types of igniters off, as they take a bit more current.

Grave Danger — $36.95
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or 5-Minute Epoxy.

Quest Sport — $10.58
What is a RockSim Design file? The RockSim software gives you a lot of information about the flight characteristics of this rocket: how high, how fast, where it will land, how will it react to wind, etc. The "design file" is intended to save you time. All the parameters (size, shape, weight, fin design, etc.) of this rocket have already been entered into the RockSim program, and saved as an electronic database file. You can just open it up in your copy of RockSim and start loading different rocket...

Ejection Charge Baffle Kits BT-60 — $5.49
"You not only show me the product and explain what it is, but you also explain why I might need to buy it. Your site does not take for granted that someone has been doing this for years and years. I've learned so much about rocketry from your site, I'm compelled to buy from you when you have what I need." -- Steven Ayers

Ejection Charge Baffle Kits AT/24 (BT-50) — $4.49
"You not only show me the product and explain what it is, but you also explain why I might need to buy it. Your site does not take for granted that someone has been doing this for years and years. I've learned so much about rocketry from your site, I'm compelled to buy from you when you have what I need." -- Steven Ayers

Box Racer — $7.49
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or White Glue. Finishing Supplies like sanding sealer, paint and sandpaper (200 and 400 grit).

Quest Complete Launch Pad System — $23.30
The launch controller from Quest is unique, and I think if far superior to the one from Estes. First, it is a pistol-grip design. That makes it easy to hold. Second, it uses a single 9 volt battery. That is much cheaper than the 4 AA size batteries that the Estes launch controller uses. And finally, it has two ways to let you know that you are ready for launch. It has both a loud alarm beeper, and a blinking LED light. The Estes controller uses a light bulb that sucks the energy out of batteries...

DynaStar Snarky — $40.78
Pencil. Ruler. Masking Tape. Hobby Knife. Razor Saw. Finishing Supplies like paint and sandpaper.

USB Data Transfer Kit — $31.75
By the way, a fresh battery lasts about 23 hours, so you don't have to worry about the rocket sitting on the launch pad for a long time before you finally launch it. The unit doesn't start recording until it detects the actual launch. While it is sitting on the pad, it is just in the stand-by mode. All this controlled by software instructions that are already built into the payload. For your part, just turn it on, and drop it into the payload bay of your rocket.

DynaStar Rip-Roar — $36.97
Pencil. Ruler. Masking Tape. Hobby Knife. Razor Saw. Finishing Supplies like paint and sandpaper.

Quest Astra Rocket Kit — $9.36
Pencil. White School Glue. Masking Tape. Hobby Knife. Finishing Supplies like paint and sandpaper.

Dynastar Firefox SHX — $52.09
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or White Glue.

Q-Modeling Viper — $68.85
Wood Glue. CyA Glue (super glue). Scissors. Pencil. Ruler. Masking Tape. Hobby Knife. Sanding Block. LONG cotton swab sticks. Finishing Supplies like paint and sandpaper, paint brushes.

54mm Diameter ROUSE-TECH MONSTER MOTORS RMS-54/2560 Hardware Set — $222.00
A. Great Question! It has to do with the physics of rocket motors. To make such an motor case, you would have to design it to fit the largest engine. Then smaller motors would have a lot of empty space in them. First of all, this would be inefficient because you're carrying excess weight into the air. The extra space that should be filled with propellant causes problems with the rest of the propellant burning. There are vibrations and acoustics that resonate in the empty chamber that make sustaining...

Airframe Coupler AC-18B — $1.61
Having Apogee's quality parts to work with is only one piece of the puzzle in making a stunning rocket. Now you need techniques and skills for assembling them into an eye-popping model. Our videos can show you the procedures and methods the experts use when they build rockets. Don't you want your rockets to be the center of attention?

Airframe Coupler AC-24B — $1.72
Having Apogee's quality parts to work with is only one piece of the puzzle in making a stunning rocket. Now you need techniques and skills for assembling them into an eye-popping model. Our videos can show you the procedures and methods the experts use when they build rockets. Don't you want your rockets to be the center of attention?

Airframe Coupler AC-29A — $1.87
Having Apogee's quality parts to work with is only one piece of the puzzle in making a stunning rocket. Now you need techniques and skills for assembling them into an eye-popping model. Our videos can show you the procedures and methods the experts use when they build rockets. Don't you want your rockets to be the center of attention?

6-Degree-Of-Freedom Simulation Software For Rocket Professionals — $111.13
Mass Of The Rocket. Moment Of Inertia. Product of Inertia. Center Of Gravity Location. Axial Force Coefficient. Normal Force Coefficient. Center of Pressure Location. Fin Cant Angle. Total Impulse Of The Motor. Propellant Mass. Thrust Axis. Wind Direction. Wind Velocity. Launch Rail Azimuth Angle. Launch Rail Elevation Angle. Ignition Failure Likelihood. CATO Of The Rocket Motor Likelihood. Deployment Failure Likelihood. Chute Failure Likelihood.

Payload Bay Selection Chart Tube Size Fits 75mm diameter — $37.95
A. See the image below. The bay will be tight. But you're a person with above average intelligence, or you wouldn't be reading this FAQ. I'm sure you'll see that a 9V battery (if your electronics requires one) will have to be housed on its side so that it is between the rails. The sled itself is made from aluminum, which is thinner than the 1/4 inch plywood in the larger electronic bays. That helps give you some additional room. Finally, the threaded rods are skinnier, which also gives you a bit...

Payload Bay Selection Chart Tube Size Fits 5.5" diameter — $54.95
A. See the image below. The bay will be tight. But you're a person with above average intelligence, or you wouldn't be reading this FAQ. I'm sure you'll see that a 9V battery (if your electronics requires one) will have to be housed on its side so that it is between the rails. The sled itself is made from aluminum, which is thinner than the 1/4 inch plywood in the larger electronic bays. That helps give you some additional room. Finally, the threaded rods are skinnier, which also gives you a bit...

Do you want tips for making dazzling rockets from your parts Balsa — $2.65
Having Apogee's quality parts to work with is only one piece of the puzzle in making a stunning rocket. Now you need techniques and skills for assembling them into an eye-popping models. Our video books can show you the procedures and methods the experts use when they build rockets. Don't you want your rockets to be the center of attention?

Tubes-O-Plenty — $19.00
Having Apogee's quality parts to work with is only one piece of the puzzle in making a stunning rocket. Now you need techniques and skills for assembling them into an eye-popping models. Our video books can show you the procedures and methods the experts use when they build rockets. Don't you want your rockets to be the center of attention?

Aerotech First Fire Igniters — $10.35
The First Fire Jr. Igniters from Aerotech, are a 2-wire igniter that are designed for easy insertion into most all composite propellant motors. They can be used in place of the Copperhead™ igniter that comes with all Aerotech motors. The "Jr" style have a smaller pyro-head so they can be fitted into smaller composite motors, like the Econojets™ . These come with 24 inch leads, giving you plenty of wire length to make hook-up fast and effortless with standard "micro-clips." These igniters require...

Electronic Model Rocket Launcher Construction Plans — $13.72
This booklet gives nine different electronic launch controller plans of varying levels of features, construction complexity, and safety benefits. You can build from a simple inexpensive controller, to a multi-pad system to launch rockets together or sequentually. All the parts for these controllers can be found at your local Radio Shack electronics store. They make great classroom projects for science technology classes.

Blue Tube 6"/48 — $64.95
"I must say I am exceptionally impressed with the speed of service in filling my orders. Your personal touch in sending e-mail notifications does not go unnoticed either. Even my wife has commented on the time and effort Apogee Rockets spends with the attention-to-detail of your customer service. I am equally impressed with the array of services your web site has to offer. It is by far the most comprehensive on the net. Thank you. I'm a new loyal customer." -- Scott A. Renshaw

Cosmodrome Black Brant II — $65.40
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or White Glue.

Sky Eagle Rocket Kit — $212.21
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or White Glue.

Hawks Hobby Super Bandit — $75.82
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or White Glue. Cotton Swabs. Finishing Supplies like sanding sealer, paint and sandpaper (200 and 400 grit).

Piston Launcher For model rockets that use an 18mm diameter motor (A, B, and C-size) — $11.24
The purpose of a piston launcher is to provide an extra kick to the rocket as it takes off. It does this by collecting the exhaust gases from the rocket engine inside a tube. As the gases build up, the pressure inside the tube increases and kicks the rocket off the pad with a higher velocity. It is estimated that the altitude increase from this can be greater than 5%. That's not bad, since you don't need to change anything else with the rocket.

Quest Zenith — $14.83
Pencil. White Glue or Wood glue. Masking Tape. Hobby Knife. Finishing Supplies like paint and sandpaper.

Lifting Body Space Shuttle from Dr. Zooch — $27.95
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. 5-Minute Epoxy or super glue. Wood Glue.

Quasar One Stratus — $24.99
Wood Glue. Scissors. Pencil. Ruler. Masking Tape. Hobby Knife. Finishing Supplies like paint and sandpaper, paint brushes.

Resin Nose Cone 10.5mm — $5.57
Choosing nose cones for your customized rockets is easy using our simplified numbering system and the charts listed here. The number following the part name tells you the tube diameter in millimeters. For example, a PNC-18 plastic nose cone will fit a 18mm dia. tube.

Vac-Form Cone 13mm — $4.31
Choosing nose cones for your customized rockets is easy using our simplified numbering system and the charts listed here. The number following the part name tells you the tube diameter in millimeters. For example, a PNC-18 plastic nose cone will fit a 18mm dia. tube.

Hawks Hobby Super Trident — $111.89
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or White Glue. Cotton Swabs. Finishing Supplies like sanding sealer, paint and sandpaper (200 and 400 grit).

Aerotech Mantis Launch Pad — $115.00
Third, the pad does require a large storage area. The legs and the rod are removable, but the plastic portion is rather bulky. Once assembled, the plastic portion does not fit back into the box it came in. If you are not going to use the pad as a display base for your great-looking rockets, you may need to find a suitable storage box for it. Another alternative is to look around in your garage for one of those folding lawn-chair sacks. It is about the same size and will hold this pad and its legs...

Apollo Capsule Set — $16.91
The 1/70th scale Apollo capsule set is all brand new! Apogee Components bought the new tooling necessary to create these exquist detailed parts. Included are the capsule (also known as the boost protect shield), the escape tower parts, a tube that fits the escape tower, Umbilical Adapter piece that connects the capsule to the Service Module, and the RCS nozzles that fit on the Service Module.

Dr. Zooch Soyuz — $25.95
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or 5-Minute Epoxy.

Add An Optional Payload Bay — $19.95
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Drill. 15 minute epoxy. 30 minute epoxy. Sandpaper. Wood Glue or White Glue. Particle mask for sanding fiberglass.

Sky Bender: The Sheer Power of a Triple-Engine Cluster — $20.25
Pencil. White Glue or Wood glue. Masking Tape. Hobby Knife. Finishing Supplies like paint and sandpaper.

Estes Igniter — $5.87
Low Current, Low Voltage. These igniters are also more forgiving of dying batteries in your launch controller. It only takes a little electricity (120 ma) to set them off. So where other igniters may not ignite, these babies will flare up and get your motors going. Please note that since they are very low current igniters, some controllers intended for "high-power" rockets can set them off during continuity tests. Be sure to hook up an igniter to your system before inserting it into the motor to...

First Time Flyer Program — $35.00
You're practically guaranteed that you'll get a successful launch. When you learn from an expert, it saves you time. Building becomes an enjoyable experience. You'll save money. Lots of money! Why? Because you won't be crashing models continuously. Lastly, your quality model will be noticed. The applause will surprise you!.

Aerotech Econojet Single-Use Rocket Motors — $20.00
The high thrust gives you the extra oomph to get those big rockets into the air. Small size - when used in smaller models, they really scream out of sight. Brilliantly colored flame color, and loud roar make them a crowd pleaser when you launch them. Anyone can use them. They are legal in all 50 states and USA Territories!. No Federal nor State Explosive Permits needed to possess or transport these motors. No "explosive storage magazine" required to store these motors in your house. Before I...

Starlight Sparrow Rocket Boosted Glider — $6.95
Pencil. Ruler. Hobby Knife. Wood Glue. Sand paper.

G-Wiz Flight Computers USB Communications Module — $34.95
4 Pyro Outputs: Pyro output 1 - Jumper select between Launch detect (for clusters) and Burnout detect (for staging). When Staging, 1st, 2nd, or 3rd stage selectable. Optional timer as well. Pyro output 2 - Fires at Apogee detect. Apogee detection is generally based on Accelerometer data, but Barometric Apogee can be selected, and is not subject to problems with Mach transition. Also with optional timer. Pyro output 3 - Fires at a programmable low altitude, settable in 100 (foot or meter) increments...

Quest Q-EZ Glider — $236.90
You'll also love the easy-to-follow instructions. There are just seven simple steps for the modeler to do to successfully assemble the rocket. While there is a tremendous sense of accomplishment felt by the child, the rocket is surprisingly very easy to put together. It can be done in as little as 30 minutes. Also, there is only one tool you'll need: a hobby knife to make a slot in the engine block ring That's it!

G-Wiz Flight Computers Basic Fight Computer — $134.95
4 Pyro Outputs: Pyro output 1 - Jumper select between Launch detect (for clusters) and Burnout detect (for staging). When Staging, 1st, 2nd, or 3rd stage selectable. Optional timer as well. Pyro output 2 - Fires at Apogee detect. Apogee detection is generally based on Accelerometer data, but Barometric Apogee can be selected, and is not subject to problems with Mach transition. Also with optional timer. Pyro output 3 - Fires at a programmable low altitude, settable in 100 (foot or meter) increments...

Mercury Engineering RDR-2 Rocket Kit — $49.00
Thick-wall cardboard tubes: They don't look thick because the tube is so large in diameter. But trust me, these tubes are meant to take a beating and survive some very rough landings. That means your rocket will last and last and last. 28-inch Diameter Rip-Stop Nylon Cloth Parachute. A kit this big, you have to have a cloth chute for the extra durability; and you get one!. Balsa wood fins. Balsa is very lightweight, so these fins help keep the tail-end of the rocket light. Because this is such...

Estes Launch Pad — $36.03
A. First, you'd need to swap out the aluminum rod with one made of steel . Aluminum is good for lightweight rockets, but you'll get too much whip of the model if the wind is breezy. Second, you would need to put a block of wood under the middle of the pad to prevent it from flexing under the weight of a heavier rocket. You should also make sure the rocket is higher on the launch rod, so the flame doesn't pound the blast deflector too hard. Otherwise, it may flex and snap off the plastic legs. Most...

18" (45.7 cm) Square — $9.74
Made from 7 oz. heavy-duty, high-visibility orange colored cloth. This makes your rocket easier to spot as it is laying on the ground after its flight. The construction of the chute protectors are entirely of Nomex, including the surging thread around the perimeter to prevent the fabric from fraying.

React-a-Pack Emergency Repair Epoxy — $4.31
Convenient Size - No waste to clean up later. And it stores easily in your range box or even a fishing tackle-box. No Mess - Mixes right in the pouch. There are no gooey bottles that leak resin if they get tipped over. This makes it perfect for storing in your kitchen drawers for those emergency repairs around the house. Portable - Fits in your pocket, or glove box of your car. Strong - Epoxy is one of the strongest types of adhesives around. Convenient Applicator - Once mixed, you can pour or...

Dr. Zooch Mercury Redstone — $24.95
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or 5-Minute Epoxy.

Quest Intrepid — $18.18
Pencil. Ruler. Masking Tape. Hobby Knife. Razor Saw. Finishing Supplies like paint and sandpaper.

Science Fair Nose Cone Project — $30.95
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or White Glue. Finishing supplies like sandpaper and spray paint.

Quasar One Eclipse — $46.99
Wood Glue. Scissors. Pencil. Ruler. Masking Tape. Hobby Knife. Finishing Supplies like paint and sandpaper, paint brushes.

Red River Predator — $25.00
Wood Glue. CyA Glue (super glue). Scissors. Pencil. Ruler. Masking Tape. Hobby Knife. Sanding Block. LONG cotton swab sticks. Finishing Supplies like paint and sandpaper, paint brushes.

Dr. Zooch Saturn 1B Skylab 2, 3, 4 & ASTP — $24.95
Pencil. Ruler. Scissors. Tweezers. Masking Tape. Hobby Knife. Wood Glue or 5-Minute Epoxy.

Cosmodrome Nike Smoke — $60.00
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue. Super Glue (CyA adhesive).

Aerotech Mustang Rocket — $68.00
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. 5-Minute Epoxy or super glue. Wood Glue.

Blue Tube 5.5"/48 — $54.95
"I must say I am exceptionally impressed with the speed of service in filling my orders. Your personal touch in sending e-mail notifications does not go unnoticed either. Even my wife has commented on the time and effort Apogee Rockets spends with the attention-to-detail of your customer service. I am equally impressed with the array of services your web site has to offer. It is by far the most comprehensive on the net. Thank you. I'm a new loyal customer." -- Scott A. Renshaw

Long March Three — $13.59
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or White Glue.

Launch Lugs — $2.24
Having Apogee's quality parts to work with is only one piece of the puzzle in making a stunning rocket. Now you need techniques and skills for assembling them into an eye-popping model. Our video books can show you the procedures and methods the experts use when they build rockets. Don't you want your rockets to be the center of attention?

Pemberton Technologies Space Ark — $119.00
Pencil. Ruler. Masking Tape. Hobby Knife. Finishing Supplies like paint and sandpaper.

Aerotech Barracuda Rocket — $74.00
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. 5-Minute Epoxy or super glue. Wood Glue.

Red River Red Strike — $19.50
Wood Glue. CyA Glue (super glue). Scissors. Pencil. Ruler. Masking Tape. Hobby Knife. Sanding Block. LONG cotton swab sticks. Finishing Supplies like paint and sandpaper, paint brushes.

Madcow Rocketry Phoenix — $99.95
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. 5 minute epoxy. Sandpaper. Lead Weight to balance the rocket. Wood Glue or White Glue.

Dynastar LexxJet — $54.25
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Razor Saw to convert (cut) the nosecone into a boattail. Carpenter's Wood Glue or White Glue. Super Glue (CyA adhesive). Sandpaper (200 and 400 grit) and a sanding block. Aluminum "Angle" to draw lines on the tube. Paint brush. Spray paint. 24mm spent engine casing to insert the engine block. Long wood dowel to spread glue deep inside the tubes.

Engine Hook Assortment — $5.25
Hold your rocket engine securely inside the tube with these metal engine hooks. Made from high strength spring steel, so they are durable and extremely stiff and rigid. Unlike cheaper hooks made from stainless steel, these won't kink when you bend them back to insert or remove the rocket engine from the model. They always spring back to shape.

Aerotech Sumo Rocket — $145.00
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. 5-Minute Epoxy. Super glue. Wood Glue.

Quasar One Delta 5 — $21.99
Wood Glue. Scissors. Pencil. Ruler. Masking Tape. Hobby Knife. Finishing Supplies like paint and sandpaper, paint brushes.

Red River Diamond Ring — $17.00
Wood Glue. Scissors. Pencil. Ruler. Masking Tape. Hobby Knife. Finishing Supplies like paint and sandpaper, paint brushes.

Stonebreaker Kit From DynaStar Mid-Power Rockets — $36.24
Pencil. Ruler. Masking Tape. Hobby Knife. Razor Saw. Finishing Supplies like paint and sandpaper.

Semroc SLS Lil' Hustler — $45.00
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or White Glue.

Features of the Aero Pack Motor Retainers Fits 38mm tubes with an O.D. of 1.630 inches, such as paper tubes from LOC — $29.00
What does it do? Simply, it also holds the engine in the rocket so it can't be spit out by a strong ejection charge. A secondary feature is that it allows you to quickly swap out the used-up motor for a new one in seconds. It is as simple as screwing off a bottle-top. Just twist off the cap, swap out the motor, and twist the cap back on to hold the engine in place.

Pemberton Technologies Krãken — $25.00
Pencil. Ruler. Masking Tape. Hobby Knife. Finishing Supplies like paint and sandpaper.

Quest Magnum Sport Loader — $15.99
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue.

Perform Real Scientific Experiments With Your Model Rockets — $13.72
Each of the more than 69 projects is fully described with background material giving the reason "why" the project will be useful and how it can be used for the future development of rockets and airplanes. Then it gives a starting point of what type of equipment may be needed. Most projects also have some hints on performing the experiment so "quality" data is gathered. At the end of each topic idea, the experimenter is given suggestions on where to find additional background research information...

Building Skill Level 2 Model Rocket Kits: Teach Others To Make Higher Quality Rockets — $23.97
Tube marking guides. Fin alignment jigs. Fin spacing guides. Sanding dowels. And much more.

Increasing the Descent Time of Rocket Parachutes — $2.40
Want a cheap rocket that can survive super sonic speeds (Mach 1, the speed of sound, is approximately 761 mph at sea level)? The Apogee Aspire is a prefect rocket for this task. It is minimum diameter for 29mm diameter high-thrust rocket engines, and it has a sleek shape that is just made for cutting quickly through the air. In this publication, you'll be shown you how to take the stock Apogee Aspire kit, and with a few simple modifications turn it into a supersonic cruising model. How? You don’t...

Obliterating Old Altitude Records — $2.40
Want a cheap rocket that can survive super sonic speeds (Mach 1, the speed of sound, is approximately 761 mph at sea level)? The Apogee Aspire is a prefect rocket for this task. It is minimum diameter for 29mm diameter high-thrust rocket engines, and it has a sleek shape that is just made for cutting quickly through the air. In this publication, you'll be shown you how to take the stock Apogee Aspire kit, and with a few simple modifications turn it into a supersonic cruising model. How? You don’t...

Screamer: Canted Motors Make it Howl at Launch — $14.24
Pencil. White Glue or Wood glue. Masking Tape. Hobby Knife. Finishing Supplies like paint and sandpaper.

Piston Launcher Plans — $1.21
Want a cheap rocket that can survive super sonic speeds (Mach 1, the speed of sound, is approximately 761 mph at sea level)? The Apogee Aspire is a prefect rocket for this task. It is minimum diameter for 29mm diameter high-thrust rocket engines, and it has a sleek shape that is just made for cutting quickly through the air. In this publication, you'll be shown you how to take the stock Apogee Aspire kit, and with a few simple modifications turn it into a supersonic cruising model. How? You don’t...

Cosmodrome Aerobee-Hi — $92.65
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. Wood Glue or White Glue.

Making Spiral-Wound Paper Tubes — $5.41
Want a cheap rocket that can survive super sonic speeds (Mach 1, the speed of sound, is approximately 761 mph at sea level)? The Apogee Aspire is a prefect rocket for this task. It is minimum diameter for 29mm diameter high-thrust rocket engines, and it has a sleek shape that is just made for cutting quickly through the air. In this publication, you'll be shown you how to take the stock Apogee Aspire kit, and with a few simple modifications turn it into a supersonic cruising model. How? You don’t...

Aerotech Mirage Rocket — $115.00
Pencil. Ruler. Scissors. Masking Tape. Hobby Knife. 5-Minute Epoxy or super glue. Wood Glue.

Selecting Rocket Motors: A step-by-step proceedure — $6.48
Want a cheap rocket that can survive super sonic speeds (Mach 1, the speed of sound, is approximately 761 mph at sea level)? The Apogee Aspire is a prefect rocket for this task. It is minimum diameter for 29mm diameter high-thrust rocket engines, and it has a sleek shape that is just made for cutting quickly through the air. In this publication, you'll be shown you how to take the stock Apogee Aspire kit, and with a few simple modifications turn it into a supersonic cruising model. How? You don’t...

Fast Rotating Model That Uses Helicopter Recovery — $17.47
Pencil. White Glue or Wood glue. Cyanacrylate (super glue) adhesive. Masking Tape. Hobby Knife. Finishing Supplies like paint and sandpaper.