421 results for "multiswitch" between $10.00 and $500.00

Zinc die-cast housing nickel-plated. Excellent quality component professional circuit design and low loss. 13/18V 0/22KHz supplied by satellite receiver through coaxial cable to switch corresponding port. Capable of connecting four SATV signals simultaneously. Four SATV signals switched through 13/18V 0/22KHz. Distributed into four subscribers to use simultaneously and no mutual interference. Applicable to multi-satellite and multi-receiver usage. Power supplied from satellite receiver or external...

Features 3x4 multiswitch LNB switched by 13-14V 17-18V from the coaxial cable SAT-TV-FM signal combined at 4 outputs 5-860MHz signal passing by ANT port Cable power from satellite receiver to LNB Impedance - 75Ohm all ports Connectors - F type female

Great device. Don't buy additional 22khz tone generators - they are already included (Smarthome needs to change the 'What's included' description). If you have more than 2 cables coming from your dish, like 4, then you need to have two short coax cables (Smarthome gives parts for do-it-yourself, but Radio Shack sells 1 ft pre-made cables) and 2 male-male connectors. This is to add the 22khz tone generators. The tone generators have a male end to the dish and a female end to the distibutor. The...

This is used to split the incoming signal from a satellite dish to multiple receivers. Supplies LNB power from the satellite receiver and does NOT require an 8014IFD power supply. It is intended for use in systems where 117VAC is not available at the distribution point where it is desired to locate a multi-switch, making these units ideal.<p><br> Includes a VHF/UHF amplifier. As such, at least one satellite receiver must be connected to model 6344IFD to pass VHF/UHF signals

Provides constant LNB voltage. Vertical voltage. High-isolation for trouble-free reception. Horizontal provided by receiver. HDTV compatible and ready. Dual LNB and amplified CATV and antenna to 12 outputs.

Dual LNB and amplified CATV and antenna to 6 outputs. HDTV compatible and ready. Vertical voltage. High-isolation for trouble-free reception. Horizontal provided by receiver. Provides constant LNB voltage.

This satellite multiswitch module is designed for quick, easy, snap-in installation into our structured wiring panels. Split the LNB signal of circular-polarized small-dish satellite systems for viewing on up to four separate IRDs. Multiplex an antenna feed for local digital and high definition programming and combine the feed from a dual LNB digital satellite dish for distribution throughout your house.

Digital Satellite Multiswitch modules by Impact Acoustics(TM) are designed for quick and easy installation into our Structured Wiring Panels. Split the LNB signal of circular-polarized small-dish satellite systems for viewing on up to four separate IRD’s. Multiplex an antenna feed for local digital and high definition programming and combine the feed from a dual LNB digital satellite dish for distribution throughout your house. Simply connect a diplexer at the receiver end to separate the two signals...

Powered multiswitch. Connect up to six DBS receivers. Provides constant 14 & 18 vDC to LNBF. Not cascadable. Off-air input and mixer.

The DECswitch 900EF module improves the configuration flexibility of your network by easily integrating Ethernet and FDDI LANs within a single standalone or hub-based architecture. It provides the switching of up to six Ethernets and high-speed FDDI networks. In addition, it can also support local layer 3 routing on a per-port basis, if desired. It has six Ethernet switched ports and one FDDI port - providing full switching and/or routing capability among each of the six Ethernets and an FDDI LAN...

1 LNB inputs to 4 outputs for 4 satellite receivers. Matrix routes between any inputs to any outputs. Territorial TV signal can be combined and conveyed by single coaxial cable. Inputs selected by 13/18V from satellite RXs. Built-in I.F. amplification circuit compensates insertion loss. 500 mA power passing from RX to LNB.

The 3x4 Multi-Switch distributes satellite signals from dual incoming LNB (Low Noise Block Converter) Digital Satellite Systems to up to four satellite receivers. The module also incorporates a separate input to receive TV antenna signals. (Best used in combination with a Video Amplifier such as Leviton?s 48210-VA.) Easy to install.

In short. the SWM-8 was designed to eliminate many of the issues involved in using house wiring in DIRECTV installs. Where previously several lines were required to run from a dish or multiswitch through outside walls and into individual rooms, the SWM-8 allows the signal to be run much more like a standard cable TV installation - only one line needs to run from the outdoor dish to the inside of the house.

Connects up to 4 satellite receivers to a dual-LNB satellite dish plus an off-air antenna or cable hookup

The Zinwell WB68 is a DirecTV approved, 6X8 multi-switch, designed to expand the new AT9 Ka/Ku Satellite Dish Antennas from 4 ouputs to 8 outputs, supporting up to 8 independently operating receivers. The WB68 supports all DirecTV Receivers, but is specially designed to work with the newest MPEG4-capable DirecTV HD Receivers such as the model H20.