148 results for "UPB" between $5.00 and $400.00

HAI 36A00-1 152358 UPB Powerline Interface Module

The SimplyBrilliant™ UPB controller line provides ultra-reliable control of new and existing lighting fixtures, lamps, fans and other electrical devices using your existing wiring to control virtually any light in your home. This eight-button keypad provides on/off and dimming control for incandescent lighting, magnetic low-voltage lighting and halogen lighting. Best of all, all faceplates are sold separately and are interchangeable in the field without ever having to untwist a wire nut, so once...

1 x Powerline 36A00-1 The Model 36A00-1 UPB Powerline Interface Module (PIM) is a plug-in module designed to interface to a serial port on an OmniLT, Omni II, or OmniPro II controller to transmit and receive UPB signals over the powerline. HAI Home Automation, Inc Not Applicable Powerline Network Adapter UPB UPB 36A00-1 Powerline Network Adapter www.homeauto.com

Authorized Dealer for the Rose Electronics RV1-15E/UPB-4U. We sell Consumer Electronics, Home Theater, SOHO PBX, Talkswitch, Bizfon, Universal Remotes, Conferencing, Panamax and Monster Cable Surge Protection, Power Inverters, etc. Worldwide Service Since 1998, Located Near San Francisco Bay Area, CA.

The Model 36A00-1 UPB Powerline Interface Module (PIM) is a plug-in module designed to interface to a serial port on an OmniLT, Omni II, or OmniPro II controller to transmit and receive UPB signals over the powerline.

15 Amp Switch Receiver can control loads directly (such as replacing the switch on the front door coach lights) or indirectly (such as switching an outlet that has a transformer plugged into it). Each Switch can be used in an On/Off mode.

Conditions in the field can be brutal on equipment. You can rely on Innotek's waterproof UPB-400 Upland Pro Beeper to take everything the elements throw at it. We took the best elements of tracking beepers to build the most durable solution. Innotek's New Upland Pro Beeper offers the value and performance you demand.

Now with Dual Setpoints (separate Heat and Cool) and Multi-Stage. Output Control. Separate Heat and Cool Setpoints. Bi-Directional UPB Control. Two part design. Set specific temperatures by X10 commands. Set modes by UPB commands. Backlit LCD Wall Display Unit. For standard gas/electric or heat pump HVAC systems. Replaces existing 4 or more wire thermostats without the need for additional wiring.

Battery kit consists of 4 Sealed Lead Acid battery(ies).

The HAI 15-Amp UPB Relay Switch uses Universal Powerline Bus technology for superior performance and reliability. Ideal for new or retrofit installations, no rewiring is necessary in order to use this switch; UPB switches require a connection to a neutral wire. UPB benefits include its higher reliability, since its signal strength is stronger than X10, with increased electrical noise resistance. UPB products are NOT X10 compatible.

INCREASES THE RELIABILITY OF THE HLC SYSTEM. FOR PROFESSIONAL INSTALLATION ONLY.

1/2" Axle diameter, 2-7/16" hub length, 600lbs capacity^Urethane on polypropylene wheel with ball bearing^95 Durometer shore a hardness^Temperature range from -40 degree F to +175 degree F

The RFI-E, Radio Frequency Interface is a plug-in interface that receives a discreet RF code from any EnOcean enabled device. Each RF code is translated into a UPB signal which is transmitted on the existing powerline. This allows control from any location with any optional EnOcean RF switch, Hand-held Key Fob remote or Occupancy Sensor

The SW-7 is not shipped with a faceplate, but it can be field upgraded with single, double (tall), double (short), triple or quad rockers in a variety of standard colors. The SW-7 can also accept a variety of multi-button faceplates to turn the transceiver into an in-wall controller. If you want to be able to upgrade a dimmer in the field, for maximum flexibility order an SW-7. See Faceplates for examples of all rocker and button faceplates.

Input and output commands to/from the X10, UPB, and FGI devices can be mapped across to the other protocols; for example, an X10 switch or a low-voltage hardwired switch could be mapped to send a UPB link command to control UPB devices, and a UPB command could be used to control an X10 device, X10 scene, or hardwired relay device. If used with a legacy X10 controller, input and output commands to/from the UPB and FGI devices can be mapped to X10 commands to the legacy X10 controller,...

The Auxiliary Switch is used in conjunction with HLC switches for multi-way lighting circuits. It can be used with any HLC Switch to make "three-way" (two switches control one light) and multi-way (more than two switches control one light) using conventio...

Features Warranty Ask a Question about this product *Your email: Question: Captcha: Text you see above: General Information Manufacturer Website Address www.rose.com Product Type KVM Switch Manufacturer Part Number UPB-4UB Manufacturer Rose Electronics Product Name UltraView Pro UPB-4UB 4-Port KVM Switch Interfaces/Ports Computer Ports 4 x 25-pin DB-25 Female Keyboard/Mouse/Video User/Console Ports 1 x 25-pin DB-25 Female Keyboard/Mouse/Video Physical...

The most capable of all FSD controllers, the Bridge Plus combines all the cross protocol integration capabilities of the X10-UPB-FGI Bridge Controller with Time of Day Controller Functions. It has twice the memory of the Bridge Controller, can support 128 devices, and can support a wide range of FGI hard-wired devices. It is the only controller you would need to support a sophisticated mixed protocol installation, but it can also be used with a legacy controller.