153 results for "RPM Planner Kit" between $10.00 and $1,500.00

Available in multiple finishes. Non-EGR. Optimized to deliver superior performance. Maximizes performance with Edelbrock carburetors. Runners tuned to match square-bore carburetors. Maximizes peak torque around 3500 RPM. For idle 5500 RPM street-driven performance. Dual-plane, low-rise intake with 180-degree firing order. Not legal for sale or use on pollution-controlled motor vehicles. In the early days of the automotive performance industry, you either ran what was available or you fabricated something...

Performer RPM; Camshaft Kit; Ford 351C; Hyd.; 1500-6500rpm; Adv. Dur. 312deg. Int./334deg. Exh.; Valve Lift .562 Int./.588 Exh.; Req. Screw-In Studs/Guideplates;

Here is a complete upper Bravo bearing kit. These bearings are an upgrade over your stock bearings. They have a higher RPM rating, which allows cooler oil temperature and better drive life.

Available in multiple finishes. Non-EGR. Optimized to deliver superior performance. Maximizes performance with Edelbrock carburetors. Runners tuned to match square-bore carburetors. Maximizes peak torque around 3500 RPM. For idle 5500 RPM street-driven performance. Dual-plane, low-rise intake with 180-degree firing order. Not legal for sale or use on pollution-controlled motor vehicles. In the early days of the automotive performance industry, you either ran what was available or you fabricated something...

Edelbrock Performer RPM Dual Quad Air-Gap Manifold and Carburetor Kits for 5.7 HEMI 03 2010 PN 2076

Right Angle Sander/grinder, Size 7 In, No-load Rpm 8000, 13 Amps @ 120v, Cord 10 Ft 2 Conductor, Spindle Thread Size 5/8-11 In, High Power To Weight Ratio, Keyless Adjustable Guard, Tool Length 16 1/8 In, Tool Weight 8.0 Lb, Bearings Ball And Roller, Handle Design Straight, Speed Type Constant, Switch Type Trigger, Includes Type 27 Wheel, Wrench, Guard, Backing Flange, Side Handle And Clamp Nut For 7/8 In Non Threaded Wheels

Designed for 1500 to 6500 Performance,Maximum Power in High-RPM with Good Low-End Torque,Matched to Edelbrock Performer RPM Intakes,10 to 12 in. of Manifold Vacuum at Idle,More Lift and Duration than Most Street Camshafts,Includes Hydraulic Lifters and Assembly Lube,Dyno Matched/Street Proven Performance,Take The Guesswork Out Of Camshaft Selection

Remove expansion plug from rear of block just below the cylinder head. Clean surface and install plate. Plumb 5/8” heater hose from plate to water pressure regulator “IN” port. Determine where you want to mount regulator and cut a section out of top radiator hose to install tee fitting. We do not supply a mounting bracket with the regulator because of the preferences of customers to locate items where they choose. A small u-bolt clamp is the simplest attaching device. Once the system is installed...

Module kit includes five modules; 200 RPM increments from 5;100 to 5;900 RPMs

Wet Polisher Kit, Size 4 In, No-load Rpm 3500, Amps @ 120 7.9, Spindle Thread Size 5/8-11 In, Cord Grounded With A Ground Fault Circuit Interrupter, Water Control Valve, Lightweight, Shaft Wrenches, Sealed Bearings, Tool Length 12 In, Tool Weight 6 Lb, Handle Design Ergonomical, Sure Grip, Speed Type Single, Switch Type Locking Lever, Includes Wet Kit, Gfci, Spanner Wrenches, 60, 150, 300, 500, 1000, 2000, And 3000 Grit Discs, Black Buff Disc And Rubber Backplate

This is the Aerospire RPM Sensor Kit. This sensor kit can be used Aerospire multigov Governor combos. Please check your manual for compatibility.

Performer RPM 5.0L Nitrous Kit SINGLE-STAGE: 150-300 HP ADJUSTABLE These nitrous kits use a patent-pending, 9/16" thick, billet aluminum spray-bar plate between the upper and lower manifold of our Performer 5.0 #3821, Performer RPM 5.0 #7126 or Performer RPM II 5.0 #7123 for power increases of 150, 200 or 300 hp in 5.0L-based Ford engines.

Includes Caliper Adaptor Bracket and Rotor. Stainless Steel. Outer Diameter: 260mm. Inner Diameter: 82mm. Thickness: 4mm.

The Universal Driveshaft RPM Kit allows you to use your own collar yet still use a quality rpm sensor. Kit includes: pick-up sensor, 2 magnets and 15' extension cable. Trigger collar and mounting bracket must be supplied by customer.

Installation Kit for RPM 150/450 and 160/460 mobile radios. Kit includes: 1 - Mobile mounting bracket; 1 - 12 VDC power cable with in-line fuse; 1 - Microphone hang-up bracket; and Hardware and installation instructions.

Kit includes: powered hall-effect pick-up sensor, 1 magnet and 15' extension cable. Trigger collar and mounting bracket must be supplied by customer.