698 results for "Four Way Splitter" between $10.00 and $25.00

The Leviton Four Way Splitter (40987-4) are designed to distribute incoming cable TV, digital cable and off-air signals to 4 locations.

1 Amplified Splitter. 4 F-female to SMB-plug cable (3 feet). 4 F-71 F-male to F-male coupler. 1 20 dB power passing attenuator. 1 SMB-jack to F-male adapter. 2 mounting screws.

Signal splitters 4 way 900 mhz 4 outputs Gold plated, 75 ohm.

Description 1 GHZ FOUR-WAY SPLITTER. This four-way splitter is compatible with digital broadcast television, digital cable television, off-air antennas and RF distribution from 5 to 1000MHz. Zinc plated, die-cast housing with precision, machined ports ensure 130dB isolation against RF leakage. 360 degree insert pins provide maximum signal transfer maintaining a distortion free signal for digital transmission. PC board technology eliminates low frequency hum and provides a clean return path for data...

This is a great way to add dimension and versatility to your lights display.

"This four-way splitter is compatible with digital broadcast television, digital cable television, off-air antennas and RF distribution from 5 to 1000MHz. Zinc plated, die-cast housing with precision, machined ports ensure 130dB isolation against RF leakage. 360° insert pins provide maximum signal transfer maintaining a distortion free signal for digital transmission. PC board technology eliminates low frequency hum and provides a clean return path for data from the cable box or cable modem. Weather...

Sending infrared signals over coax? Then consider using this splitter from Xantech. Specially designed for IR distribution applications, the splitter allows signals from IR receivers to pass through, eliminating the need for a bypass kit. Splits 1 input to 4 outputs.

CONNECTS 4 TVS OR A COMBINATION OF TV, VCR, ETC., FROM A SINGLE SIGNAL SOURCE

Divides signals from single 75 ohm coaxial line into four trunk lines. Input and output are 75 ohm unbalanced type; connectors are BNC-type for RG-6/U, RG-59/U or RG-11/U cable.

The splitter is compatible with either satellite radio system. The splitter will pass the DC voltage supplied by a radio at any output port to the splitter input port. This will provide power to any antenna connected to this port for the antennas internal low-noise amplifier (LNA). Standard RG-6 cable with male F-connectors (not supplied) can be used to extend the output cable lengths.

Meets or exceeds frequency range and RF shielding specifications for use with digital and broadband cable services.

NorthStar wedge slips over present wedge and converts it to a four way splitter for FAST splitting. For use on horizontal, hydraulic log splitters. Application: Slip-on wedge, Compatible ...

This tool is designed for the CATV installation contractor for crimping F type compression fittings on RG6, 59, 7 and 11. The rotating connector positioner allows for quick change of fittings with no adjustments required. Crimp height is fixed for PPC's EX-XLWS A...

This Four-Way Wedge slips over the existing WoodEze 4 Ton logsplitter wedge and converts it to a four way splitter for faster splitting. Simply slide it down over the wedge and your ready to go. If you need or want to use only the main wedge, just lift the 4 way wedge off and set it aside for use later.

If you want to use any PlasmaGlow Truck Products, like the Fire & Ice Tailgate Bar or Mud Flap Kit, that utilize the 4-pin trailer hitch plug and pull your trailer at the same time, your only option was to hard-wire your lighting accessories. This 4-Way Trailer Hitch Adapter Splitter will allow you to plug up to 4 products into the trailer hitch plug on your truck without having to do any complex wiring. It will fit any truck with a 4-pin flat trailer hitch adapter. If you have a round trailer...