237 results for "4"" Fire Stop Support (AL29-4C) For Tankless Water Heater" between $25.00 and $700.00

For Use with RC98 and R98LS Models GSA Approved Resists Chloride Ion Pitting, Crevice Corrosion And Stress Corrosion Cracking Made From Superferritic Stainless Steel Professional Installation Recommended, Weight: 1 lbs., Manufacturer: Rinnai

For Use with RC98 and R98LS Models GSA Approved Resists Chloride Ion Pitting, Crevice Corrosion And Stress Corrosion Cracking Made From Superferritic Stainless Steel Professional Installation Recommended, Weight: 1.5 lbs., Manufacturer: Rinnai

If penetrating a ceiling, some local codes may also require a Fire Stop (SKU# 2SVSFSF04). If pipe support is also needed, use a Fire Stop Support (SKU# 2SVSFSSF04) instead.

4" stainless steel venting for Category III Gas Appliances is the perfect venting option for the Bosch Aquastar 240FX, Aquastar 125FX, Takagi TK1, TK2, TKD20, TKJR, TK1S, TM1 Tankless Water Heaters. Our Z-Flex Z-Vent venting is rated AL29-4C.

Superior, reliable performance Superior technical support Simple design of plumbing system Sleek design fits in anywhere No venting required, Weight: 16.4 lbs., Manufacturer: Stiebel Eltron

Up to 50% less power cinsumption compared to storage type heaters Instant hot water Built in scald guard thermostat Lower installation costs compared to tank type units Ultra reliable, Weight: 5.3 lbs., Manufacturer: Stiebel Eltron

Any claim for warranty assistance must be made promptly. First, determine if your water heater is “in-warranty” (that is, within the Applicable Warranty Period).You can determine your unit's warranty status by adding its Applicable Warranty Period to its date of installation. However, if you do not have documentary proof of your water heater's date of installation, your unit's warranty status will be based on its date of manufacture. The first four digits of the unit's serial number represent the...

N-Vent is UL approved Category III Stainless Steel venting. Underwriter's Laboratories (UL), an independent not-for-profit product safety testing and certification organization is one of the most recognized safety agencies in the world. N-Vent is approved for tankless and boiler stainless steel exhaust installations at a fraction of the industry standard cost.

Zero Clearance To Combustibles Single Penetration Through Wall For Both Intake And Exhaust GSA Approved May Be Required By Local Or State Code Professional Installation Recommended, Manufacturer: Rinnai

Supply hot water for 1 regular sink or up to 3 low flow sinks at 1.3 GPM at 45F raise 3-in-1 capacity options: Setting 1 at 8.5kw/40amp, Setting 2 at 6.4kw/30amp, or Setting 3 at 4.2kw/20amp Includes: heater, owner/installer manual, mounting bracket, pressure relief valve, inlet water filter, template and mount screws Install at point of use, Green technology saves up to 50-percent energy and supplies instant hot water in 2 seconds flat Qualifies for LEED points, meets NAHB green building standards...

Model: DHC-4-3. Product Type: Tankless Water Heater. Product Dimensions: L: 4.13" x W: 7.88" x H: 14.19". Product Weight: 4.60 lbs. Product Color: White/grey. Application: Ideal for restrooms or kitchenettes in an office or commercial/industrial setting or for cabins, boats, and RV's. Warranty: 3-year limited manufacturer's warrany. Voltage: 277 volts. Watts: 4500 watts. Amps: 17 amps. Certifications: ETL , ISO. Fuel Type: Electric. Type: Point of Use. Usage: Bathroom sinks, kitchen...

* Phase1, 208/240V, 2.9/3.8 KiloWatts, 14/16 Amps. * Minimum required circuit breaker size 20 Amps. * Recommended wire size AWG Copper 12. * Minimum water flow to activate unit 0.42 GPM/1.6 l/min. * Pressure loss in unit 2.88 PSI/0.23 bar. * Maximum working pressure 125 PSI/10 bar. * Tested to pressure 250 PSI/20 bar. * Water connections 1/2" NPT. * Dimensions: H 14-3/16" x W 7-7/8" x D 4-1/8".

By putting the hot water right where it is needed, you can reduce pipe runs from a central hot water tank. This reduces the use of water and energy. The smaller tank coupled with good insulation also reduces the stand-by losses in comparison with larger tank type water heaters.

224270 N/A 39Â" Metal Vent Pipe Extension for Non-Condescing Tankless Water Heaters

3/4" Standard connections. Pressure relief valve. Accepts industry standard 10" cartridges. Clear housing bowl for easy filter cartridge inspection. Reinforced polypropylene head. Clear Styrene acrylonitrile (SAN) bowl. Securely retained Buna "N" O-ring to ensure effective sealing. Positive head to bowl "stop" to prevent overtightening. Tested and certified by NSF International under ANSI/NSF Standard 42 for material and structural integrity requirements.

For Use with RC98 and R98LS Models GSA Approved Resists Chloride Ion Pitting, Crevice Corrosion And Stress Corrosion Cracking Made From Superferritic Stainless Steel Professional Installation Recommended, Weight: 1 lbs., Manufacturer: Rinnai

The heating elements are controlled by a flow switch and by an exclusive scald-guard thermostat, which keeps the water temperature within safe limits at all times. In addition, the DHC water heaters are equipped with a safety high-limit with manual reset. The rugged all copper design of the Stiebel Eltron DHC Heater ensures many years of reliable service.

Model: DHC-4-2. Product Type: Tankless Electric Water Heater. Product Dimensions: 4.13 x 7.88 x 4.19. Product Weight: 5.30. Product Color: White/grey. Application: Ideal for restrooms or kitchenettes in an office or commercial/industrial setting or cabins, boats, and RV's. Warranty: 3-year limited manufacturer's warranty. Voltage: 240 volts. Watts: 3800 watts. Amps: 16 amps. Certifications: ETL, ISO. Fuel Type: Electric. Type: Point of Use. Usage: Bathroom sinks, kitchen sinks, and laundry...