|
3-3/4" Garage Door Torsion Spring Cones
Garage Door Torsion Spring Cones We offer Winding and Stationary Cones in sets, or assembled to our Springs. Winding Cones fit into torsion springs to permit winding and tension adjustment. Stationary Cones fit into the end of a torsion spring permitting the spring to be fixed to the center bearing bracket, and may also incorporate a retainer for a ball bearing or a nylon bushing. For a complete list of our Garage Door Springs Click Here 
|
$16.50
|
Top stores
North Shore Commercial Door
$16.50
|
|
2-5/8" Garage Door Torsion Spring Cones
Garage Door Torsion Spring Cones We offer Winding and Stationary Cones in sets, or assembled to our Springs. Winding Cones fit into torsion springs to permit winding and tension adjustment. Stationary Cones fit into the end of a torsion spring permitting the spring to be fixed to the center bearing bracket, and may also incorporate a retainer for a ball bearing or a nylon bushing. For a complete list of our Garage Door Springs Click Here
|
$7.60
|
Top stores
North Shore Commercial Door
$7.60
|
|
Garage Door 2" Torsion Springs with Installed Cones
Torsion spring coated and oil tempered and include winding and anchor cones installed. Springs are factory coated black for smoother, cleaner operation. For use on doors 7' high with 4" standard lift drums. Engineered for maximum application range. Minimum 10,000 cycles, at +/- 7.5lbs of target door weight. Springs are made of steel coils with aluminum cones.
|
$36.99
waynedaltonparts.com
|
Top stores
waynedaltonparts.com
$36.99
|
|
Garage Door Torsion Springs 2-5/8" ID for Commercial Garage Doors
Measure the inside diameter to the nearest 1/16th of an inch. In most cases, the cones inserted in each end of the spring will have a manufacturers name (OHD or Raynor, etc.) which will give a clue toward the proper identity. The chart on the right shows common ID’s used by various manufacturers. If no manufacturers name is evident, usually a part number on the cone will indicate the inside diameter: 134 or 175 = 1 3/4" ID 258 or 263 = 2 5/8" ID 375 or 334 = 3 3/4" ID
|
$54.75
|
Top stores
North Shore Commercial Door
$54.75
|
|
Garage Door Torsion Springs 3-3/4" ID for Commercial Garage Doors
Measure the inside diameter to the nearest 1/16th of an inch. In most cases, the cones inserted in each end of the spring will have a manufacturers name (OHD or Raynor, etc.) which will give a clue toward the proper identity. The chart on the right shows common ID’s used by various manufacturers. If no manufacturers name is evident, usually a part number on the cone will indicate the inside diameter: 134 or 175 = 1 3/4" ID 258 or 263 = 2 5/8" ID 375 or 334 = 3 3/4" ID
|
$98.00
|
Top stores
North Shore Commercial Door
$98.00
|
|
Garage Door Torsion Spring Replacement
Resetting the drums, if needed: If the drums were incorrectly set in their old positions, one must reset both drums in new positions on the shaft. This is complicated by the presence of old dimples in the torsion shaft from previous setting(s), which must be avoided lest they improperly influence the new setting of the drums. To begin this process of resetting the drums, the door must first be lowered and resting level on the floor, the spring(s) must be in the unwound condition with...
|
$50.00
truetex.com
|
Top stores
truetex.com
$50.00
|
|
Garage Door Torsion Springs 3-3/4" ID for Commercial Garage Doors
**We always recommend replacing your garage door springs in pairs on doors with 2 springs. The reason is that springs are designed to open and close the door a predetermined number of times. Simply put if one spring broke, the other spring is going to too.** The four specific items required to purchase the correct replacement torsion spring. #1 Wire Size #2 Inside Diameter #3 Length of spring #4 Wind of spring (Right or left wound) WIRE SIZE: A springs wire size can be determined by...
|
$98.00
|
Top stores
North Shore Commercial Door
$98.00
|
