31 results for "1-9/16" Spline Rotary Hammer Kit" between $100.00 and $800.00

11.0 Amp motor delivers high output and overload protection. Electronic variable speed allows the user to control the speed of drilling and chipping. 7.3 ft-lbs of impact energy provides fast drilling and powerful chipping. Rubber grip helps reduce the level of vibration felt by the user. Rear handle mount means less bending over when using tool in down drilling applications. Factory-set clutch reduces sudden, high torque reactions if bit jams. Modular construction allows service technicians...

1-9/16-in Spline Combination Rotary Hammer Kit - D25553K. 360&*176; Side Handle. Depth Rod. Kit Box

* Built for continuous, large, deep hole. * Hard-hitting hammer mechanism. * Dual-wall housing construction. * Multiple seals prevent dust from entering. * Switch and brushes designed for long life. * Highly efficient cooling system. * Rear mount for side handle. * Factory set clutch.

Factory clutch helps reduce the tools reaction to embedded steel when bits "lock-up" while in operation, preventing injury

Patented Vibration Isolation System (both grips). Single motion bit insertion and positionable chisel lock. 1-1/2 in. bit capacity, 6 in. thin wall core bit capacity. Dial speed control: 190-385 rpm, 1700-3400 bpm. Powerful 11.0 amp motor with Electronic Feedback Control Circuit. Includes 12 in. Bull Point Chisel, Flat Chisel, two 4-cutter carbide drill bits (5/8 in. and 3/4 in.), and LHS Shank (Spline Drive).

Features more power, lighter weight, less vibration and lower noise than its well known predecessor. Powerful 8.4 Amp motor delivers 950 watts of input power for maximum productivity. Produces 5.9 ft/lbs of impact energy for faster drilling and chiseling through concrete. Two modes of operation - hammer only and hammer drilling controlled by the simple turn of a knob. Low vibration levels of only 18.8m/s2 (full load) for more comfortable operation in hand. Low noise levels of only 95.2 dB (full...

* Suitable for bits and accessories with SDS max shank end, spline shank end or ratio thread. * Rotation stop. * Metabo CODE! System: Electronic theft protection, code activated key (accessory). * Vario Tacho Constamatic (VTC) full-wave electronics. * Thumbwheel speed control. * Pneumatic high-performance hammer mechanism. * Magnesium die cast gear housing. * Ergonomic housing design for fatigue-proof operation. * Rubber-coated handle. * Torque limiting clutch. * Auto-stop carbon brushes...

Low viscosity grease should be applied to the Hammer Drill so that it can be used for a long period without replacing the grease. Weight: 17 Lbs

Powerful 24V (2.0Ah) Ni-MH MAKSTAR™ battery for longer run time 3 mode settings for hammering, drilling, and rotation with hammering Well balanced for easy handling D-handle design with ergonomic rubberized grip High performance "Makita" motor lasts up to 5 times longer One touch sliding chuck for easy bit installation Electric brake2 ea. Ni-MH Battery BH2420 (193737-7) Charger DC24SA Side handle (152521-9) Depth gauge (321144-6) Bit Grease (181573-3) Plastic tool case (152790-2) Capacity Concrete...

Features: 8.3 Amp motor provides high performance and overload protection Hard-hitting hammer mechanism for fast and efficient penetration Fully sealed gearbox engineered for long life by keeping grease in and dust out Accepts SDS bits from 5/32" to 1-1/8" Higher drilling capacity than compact drilling hammers for increased productivity in 1/2" & larger applications Less weight than large drilling hammers reduces user fatigue in 5/8" & smaller applications Chipping (Hammer-Only) mode allows...

In no event shall Makita be liable for any indirect, incidental or consequential damages from the sale or use of the product. This disclaimer applies to both during and after the term of this warranty. Makita disclaims liability for any implied warranties, including implied warranties of "merchantability" and "fitness" for a specific purpose, after the one-year term of this warranty. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state....

All ball and needle bearings for longer tool life Powerful 10 AMP motor for continuous heavy duty work Torque limiting clutch Easy lever change from "rotary hammering" to "hammering only" Automatic brush cutoff to advise maintenance schedule and to protect motor "Spline" type drive system for maximum power Factory grease packed for reduced maintenanceNCLUDES: Hex wrench (#4; 783202-0, #5; 783203-8) Plastic tool case (150589-9) Capacity Concrete (with core bits) 4-5/8" No Load RPM 240 Blows...

Spline Carbide Drill Bits are designed for use in a rotary hammer equipped with a spline type chuck. The bits are manufactured to conform with ANSI Standard B212.15 and can be used to drill in concrete, block, brick, and soft stone

Voltage 120 AC Only. Amps 11.0. No Load Speed 190/385 RPM. No Load BPM 1,700/3,400. Blow Energy 7.9 ft.-lbs. Cord Type 10 ft. Quik-Lok Drilling Mode. Hammer with Rotation & Hammer Only. Handle Style D. Handle Vibration Reduction Yes. Electronic Feedback Yes. Clutch Yes. Solid Bit Capacity 1-1/2 in. Thick Wall Core Bit Capacity 4 in. Length 17-1/2 in. Tool Weight 14.2 lbs. Shipping Weight 32.0 lbs.