790 results for "1000 watt power amplifier" between $50.00 and $700.00

This two-channel rack-mountable amp's got power – 1000 watts! Each input takes RCA, XLR, or ¼” phono. Control each channel with an illuminated knob. A clipping LED reminds you to turn it down if your signal is distorted. Use in stereo, mono, or bridge mode for maximum output. Connect your speakers using the two Speakon inputs, or use the shock-free banana plugs on the back. The heavy duty fan with aluminum heat sink and protection circuit guards your equipment for optimum performance.Features: ...

Dual XPE1700 1000W Max Mono MOSFET XPE Series Power Amplifier creates maximum power at 1 ohm loads to drive any subwoofer system to it full potential.

Product Features:1000w Peak, 4-channel Class D Power AmplifierRms Power Rating: 8 Ohms: 150 Watts X 4 Chan.4 Ohms: 250 Watts X 4 Chan.Bridged, 8 Ohms: 500 Watts X 2 Chan.Integrated Protea Dsp Allows Graphic And/or Parametric Eq, High And Low Pass Filters, Time Delay, Etc.Rackmount Design Allows You To Install The Amplifier In Any Standard Equipment Rack10/100 Ethernet Jack That Allows You To Control And Monitor The Amplifier's FunctionsMixer Section Allows You To Route An Input To Any And All OutputsEthernet...

*1000 Watts of Power with 30% Smaller Chassis Size. *CEA Rated: 300W (1.0% THD+N) (4Ohm/1Ch). *CEA Rated: 500W (1.0% THD+N) (2Ohm/1Ch). *High Quality Speaker Level Input and Blue Illumination. *Variable low-pass filter (50-200 Hz at -24 dB per octave). *Bass Boost Control 0-18 dB at 40 Hz). *Infrasonic filter (15/25 Hz, 18 dB/octave). *Speaker-level inputs with signal sensing turn-on. *Preamp-level inputs and outputs. *11-1/16"W x 2-3/8"H x 9-7/8"D .

Grow Your Passion! Output power: 1000W @ 4 ohms; 1400W @ 2 ohms Front mounted two low pass filters and two gain controls Advanced performance 3rd generation circuitry design High continuous current output from robust toroidal transformer Switchable input peak limiter and selectable high pass filter (30Hz, 50Hz) to reduce distortion and protect Speakers Bridge mono and parallel mode LEDs Fast Recovery design for lower distortion if clipping occurs Very rugged housing Active balanced inputs for low...

This power amplifier features Class-D technology for reliable, cool-running performance and thermal overload protection on each channel for safe use.

BEHRINGER’s new EPQ power amps are built for the working musician. They are exceptionally light, they pack massive power and they are built to last through all the rigors of the road. Plus its light price tag will leave you with enough cash left over to acquire more stuff to amplify!

1000 Watt professional power amplifier with a Dual VU Output Level Meters,Meter Range Selector, A/B Speaker Selector Dual RCA & 1/4” Inputs, Switched AC Accessory Outlet Protection & Clip Circuitry, Fan Cooled, Headphone Jack 2 Year Warranty.

Two Channels A/B- Bridgeable. Inputs: Electronic Balanced; Barrier Strip ,XLR,TRS 1/4''. Speaker Terminal: Speakons for Ch A, Ch B and Bridge; Binding post. Cooling Fan Two-speed DC fan, air Flow back to front. 110/220 Volt Switchable. 2x5 LED Indicator Red ,DDT / Clipping; Yellow, signal; Green ,power. Overload and Protection Indicator. Signal/Noise ratio: =102dB. Distortion: =1.0%. Frequency response: 20Hz-20 KHz >±0.5dB. input impedance: balance 20Khz. Input level:+4dB. Total Power...

* 1000 Watts @ 4 ohms. * 1900 Watts @ 2 ohms. * Can power 1, 2, 3, or 4 ButtKicker LFE transducers. * Class D switching technology. * Variable high cutoff, 40 - 160 Hz. * Low cutoff, 25 Hz switchable. * RCA and 1/4” inputs with 160m Volt and 1.25 Volt sensitivities.

* 1000 Watt IPP (Instant Peak Power) High Power Output.

Dual VU Output Level Meters. Meter Range Selector. A/B Speaker Selector. Dual RCA & 1/4' Inputs. Switched AC Accessory Outlet. Protection & Clip Circuitry. Fan Cooled. Headphone Jack.

Behringer EP2000 Stereo Power Amplifier Protected by an impact resistant, all-steel 2U rackmount chassis, the Behringer EP2000 Stereo Power Amplifier comes with ATR (Accelerated Transient Response) Technology. The EP2000 delivers precise power, signal and clip LEDs to monitor performance. For reliable operation, independent DC and thermal overload protection on each channel, a back-to-front ventilation system, high-current toroidal transformer and power transistors have been added. With rugged...

1000W RMS x 1 at 2 ohms. 600W RMS x 1 at 4 ohms. 320W RMS x 1 at 8 ohms. 900W RMS x 2 at 2 ohms. 530W RMS x 2 at 4 ohms. 300W RMS x 2 at 8 ohms. 2- Channel independent fourth-order Linkwitz-Riley crossovers. DDT protection. Revolutionary IPR class D topology. Detented input controls. Combination XLR 1/4" inputs. 4 pole twist lock output connectors. Ultra-light weight. Individual signal pass 1/4" jacks on each channel. LED illuminated. Standby, LED power present indication. Weight...

A subwoofer reduces strain on the full-range speaker, allowing it to play louder, or letting a smaller speaker do the same job. The GX Series supports this mode with a Crossover switch that splits the full-range input entering Ch 1, sending 20 Hz -100 Hz to the sub (Ch 1) and 100 Hz - 20 kHz to the top box (Ch 2). The front panel gain controls balance the sub and top box, while GuardRail optimizes peak power into the sub and top individually, for greater musical impact and dynamic range. GuardRail...

The GX5 uses a Class H system, based on key elements of the PL Series, (PLX, PL3, CX, DCA) almost doubling power in the same size and weight. QSC design expertise allows the output devices to shift from low-power to high-power rails in less than a millionth of a second, ensuring that the output power is always right where it needs to be without excess loss. Both amplifiers use premium toroidal power transformers for reliable "mid-weight" performance. A variable-speed fan...

The Accuphase P-370 features a 3-parallel push-pull output stage that delivers linear power into ultra-low impedance loads. Its current feedback circuit topology combines excellent sound quality with total operation stability. Furthermore, bridged connection mode allows upgrading to true monophonic amplifier. Other features include massive Super Ring toroidal transformer, balanced inputs, and two sets of large speaker connnectors.

Fill out the form below for more information about the CALIFORNIA INSTRUMENTS 1001TC