|
Throttle Cable Clamp (ea)1"
Clean up the look of your bike with these two-piece chrome-plated die-cast clamps that keep cables and oil lines where they belong.
|
|
|
|
|
|
|
|
|
Biker's Choice Single Cable Throttle Clamps 1-inch Handlebars (Cable Throttle Clamps)
Die cast. Chrome-plated.
|
|
|
Chrome clamp for your dual throttle cable to enhance the overall look of your bike. Fits 1" handlebars.
|
|
|
Cable Clamp, 1" - 1.125" Dual Throttle/Clutch
Swivel head design allows more natural cable routing without excessive bending
|
|
|
|
|
|
Alternate to V07-179 - Solderless Nipple. This comes with a small hex head bolt instead of countersunk regular screwdriver head bolt. Fits headset pulleys.
|
|
|
surfaces and cable housing. 1 clamps fit handlebars and aftermarket
|
|
|
Details Reviews Related Items CHROME BILLET DUAL HOLE THROTTLE CABLE 1" DIAMETER CLAMP FOR 1982 TO PRESENT HARLEY MODELS & METRIC CRUISERS (EACH) Fits Harley models 1982 to present and Metric Cruisers Chrome billet 2-piece dual hole throttle cable clamp For 1" diameter handlebars Sold each
|
|
|
Kuryakyn Throttle Cable Clamp 1-1/4 inch
Didn't end up putting it on my bike, when I held the cables that close to the bars, the throttle didn't return the way it should? They look good and perhaps would work better with stock bars?
|
|
|
THROTTLE IDLE CABLE CLAMP made by Biker's Choice Application: See description in catalog at Link to Catalog Page
|
|
|
For 1-38 diameter bar.Clean up the look of your bike with these two-piece chrome-plated die-cast clamps that keep cables and oil lines where they belong.
|
|
|
|
|
|
All orders for this part are considered special order and will be brought in from Europe when ordered. For this reason, this part is non returnable except for direct exchange for the same part# if defective
|
|
|
Sleek design. Chrome plated. Mounts to handlebar.
|
|
|
|
|
|
Ness-Tech Dual Throttle Chrome Die-Cast Aluminum Cable Clamp 1"
Chrome plated cable clamps have a billet look with a die-cast construction. Sold each.
|
|
|
|
|
|
Available in 1" or 1-1/4" Size. Chrome.
|
|
|
Highway Hawk Throttle Cable Clamp
A little cheap for the low cost should be $2-$5 and should be a way to get the different colors like the picture, but it will do the job.
|
|
|
CLUTCH AND THROTTLE CABLE CLAMPS
Get your cables under control. Made of a tough, semiflexible elastomer that not only holds your cables in place, but also minimizes vibration and wear caused by steel clamps. Unique design of clamps allows them to be snapped in place quickly and easily onto 1 1/8 through 1 1/4 diameter tube frames. PART #0658-0002 secures one standand clutch cable with a 5/16 o.d. PART #0658-0001 secures two standard throttle cables with a 1/4 o.d. Sold in pairs.
|
|
|
Clean up the look of your bike with these two-piece chrome-plated die-cast clamps that keep cables and oil lines where they belong.
|
|
|
Throttle cable pinch bolt for use with universal inner throttle cable #1005.A. When used with plastic or aluminum Serveta/SIL/late Innocenti type throttle pulleys, a small slot or hole must made in the pulley to allow the excess cable to pass through.
|
|
|
Biker's Choice THROTTLE IDLE CABLE CLAMP 61090
|
|
(US)
