|
Rear Bumper by Hanson OffRoad
JK Rear Bumper with spindle mount for a tire carrier. This is the rear bumper only, it has the spindle attached so that you can add a tire carrier in the future, #CTC2-P. Bumper is made of 3/16 steel, that is laser cut and formed. It has a built in 2" receiver. The tire carrier mounts to our spindle that has been in use for years with great success.
|
$879
See 2 Stores
See All Stores
|
|
Bumper and Tire Carrier by Hanson OffRoad
JK Rear Bumper with spindle mount tire carrier. Bumper is made of 3/16 steel, that is laser cut and formed. It has a drop down deck in it to allow the rear tire to be mounted lower. It has a built in 2" receiver. The tire carrier mounts to our spindle that has been in use for years with great success. The tire carrier, carries a 37" tire with no problems or rattles. It will carry a 48" HiLift as shown in the picture. Tire carrier opens effortlessly. It uses a bear claw latch very similar to a car...
|
$1,299
See 3 Stores
See All Stores
|
|
The handcrafted construction of this sturdy bumper consists of 3/16 cold rolled steel, 3/8 end plates, frenched-in 2 receiver hitch and 1 clevis tabs. The combination of sturdy construction and multiple angles adds strength and optimizes departure angles. The unique placement and design of the 1 wide clevis tabs gives them unmatched strength allowing them to be pulled from any angle without fear of damage to bumper or tab, and do not interfere with departure and approach angles. Frame reinforcement...
|
|
|
Hanson OffRoad XJ Rear Bumper
The combination of sturdy construction and multiple angles adds strength and optimizes departure angles. The unique placement and design of the 1 wide clevis tabs gives them unmatched strength allowing them to be pulled from any angle without fear of damage to bumper or tab, and do not interfere with departure and approach angles.
|
$725
See 2 Stores
See All Stores
|
|
60" Rear Bumper by Hanson Enterprise
Hanson Enterprise Bumpers use patented 45° forming for better approach and departure angles and are constructed of tough 3/16 thick hot rolled plate steel with 3/16 thick mounts and 1 thick high-yield steel clevis tabs. Front bumpers have a winch deck that is dropped 2” for better airflow and lower center of gravity, and they come with a 1/4 thick fairlead mounting plate that fits most planetary gear style winches. Rear bumpers incorporate a 2 receiver and an optional 1-3/4 diameter greasable spindle...
|
$451
See 3 Stores
See All Stores
|
|
Rear Bumper with 2” Receiver by Hanson Enterprise
The handcrafted construction of this sturdy bumper consists of 3/16” cold rolled steel and frenched-in 2” receiver hitch. The combination of sturdy construction and multiple angles adds strength and optimizes departure angles. This bumper wraps around the rear body with a thinner profile than stock bumpers. Integrated hitch does not interfere with ground clearance or departure angles. It is available in a black semi-gloss powder coat or bare steel.
|
$898
See 2 Stores
See All Stores
|
|
The handcrafted construction of this sturdy bumper consists of 3/16” cold rolled steel, 3/8” end plates, frenched-in 2” receiver hitch, 1” clevis tabs and 1 7/8” machined spindle. The spindle is inserted and welded in with reinforcements to accommodate tire carrier and cargo system components. The combination of sturdy construction and multiple angles adds strength and optimizes departure angles. The unique placement and design of the 1” wide clevis tabs gives them unmatched strength allowing them...
|
|
|
The handcrafted construction of this sturdy bumper consists of 3/16” cold rolled steel, 3/8” end plates, frenched-in 2” receiver hitch and 1” clevis tabs. The combination of sturdy construction and multiple angles adds strength and optimizes departure angles. The unique placement and design of the 1” wide clevis tabs gives them unmatched strength allowing them to be pulled from any angle without fear of damage to bumper or tab, and do not interfere with departure and approach angles. Frame reinforcement...
|
|
|
Hanson OffRoad JK Rear Bumper
JK Rear Bumper The handcrafted construction of this sturdy bumper consists of 3/16 cold rolled steel and frenched-in 2 receiver hitch. The combination of sturdy construction and multiple angles adds strength and optimizes departure angles.
|
$879
See 2 Stores
See All Stores
|
|
Square Frame Tire/Cargo Carrier by Hanson Offroad
Hanson’s Spare Tire/Cargo Carriers will secure up to a 37 spare using a three lug nut mounting plate that works with most factory and aftermarket rims. The Square Frame Tire/Cargo Carrier has provisions for mounting additional Hanson Cargo Racks and a Hi-Lift® Jack while the A-Frame Spare Tire Carrier does not. Both Tire/Cargo Carriers have mounts for auxiliary lights and an antenna, and they swing out and latch at approximately 90 degrees to the rear of your Jeep®. Constructed of .120 wall steel...
|
$498
See 2 Stores
See All Stores
|
|
Auxillary Pin Yoke by Hanson Offroad
Hanson’s Spare Tire/Cargo Carriers will secure up to a 37 spare using a three lug nut mounting plate that works with most factory and aftermarket rims. The Square Frame Tire/Cargo Carrier has provisions for mounting additional Hanson Cargo Racks and a Hi-Lift® Jack while the A-Frame Spare Tire Carrier does not. Both Tire/Cargo Carriers have mounts for auxiliary lights and an antenna, and they swing out and latch at approximately 90 degrees to the rear of your Jeep®. Constructed of .120 wall steel...
|
$58
See 2 Stores
See All Stores
|
|
The handcrafted construction of this sturdy bumper consists of 3/16 cold rolled steel, 3/8 end plates, frenched-in 2 receiver hitch and 1 clevis tabs. The combination of sturdy construction and multiple angles adds strength and optimizes departure angles. The unique placement and design of the 1 wide clevis tabs gives them unmatched strength allowing them to be pulled from any angle without fear of damage to bumper or tab, and do not interfere with departure and approach angles. Frame reinforcement...
|
|
|
Add that much needed step to your rear bumper. Heavy Duty Step Bumper is constructed entirely of heavy duty 120 wall steel. The step is plated with a perforated laser cut step surface. The lasercut perforated plate is 2x thicker than other products on the market. It will not bend.
|
|
|
The handcrafted construction of this sturdy bumper consists of 3/16” cold rolled steel, 3/8” end plates, frenched-in 2” receiver hitch, 1” clevis tabs and 1 7/8” machined spindle. The spindle is inserted and welded in with reinforcements to accommodate tire carrier and cargo system components. The combination of sturdy construction and multiple angles adds strength and optimizes departure angles. The unique placement and design of the 1” wide clevis tabs gives them unmatched strength allowing them...
|
|
|
Rear Bumper Guard by Black Horse Off Road 08-09 Buick Enclave (8D009701A)
Why protect just the front of your SUV or CUV when lots of accidents happen from behind? The Black Horse rear bumper guard was created to provide better all-round protection for your SUV or CUV. It's also designed to fit without interfering with factory tow hitch packages. Available for most late-model SUVs and CUVs, the rear bumper guard bolts on in less than ten minutes. Available in double and single tube, the Black Horse rear bumper guard provides stylish protection and good looks. Easy...
|
$189
See 4 Stores
See All Stores
|
|
1997-06 TJ Wrangler, Rubicon and Unlimited. Black powder coat. Spindle for tire carrier option. Made from heavy duty 3/16" hot rolled plate steel. 3/8" mounting plates and end caps. 2" receiver. Welded-on 1" clevis tabs with 7/8" hole.
|
|
|
Hanson Offroad 60" Basic Rear Bumper with Tire Carrier
The handcrafted construction of this sturdy bumper consists of 3/16 cold rolled steel, 3/8 end plates, frenched-in 2 receiver hitch, 1 clevis tabs and 1 7/8 machined spindle. The spindle is inserted and welded in with reinforcements to accommodate tire carrier and cargo system components. The combination of sturdy construction and multiple angles adds strength and optimizes departure angles. The unique placement and design of the 1 wide clevis tabs gives them unmatched strength allowing them...
|
$1,098
See 2 Stores
See All Stores
|
|
The tire rack is constructed of .120 wall tubing. Features an easy open bear claw latch operation with an integrated bottle opener, a detent mechanism that locks the tire carrier in an open position, antenna mount, and hi lift jack mount. Upper hinge arm adds strength for heavy loads and prevents rattling. Accommodates 37 tires and multiple wheel lug patterns.
|
|
|
The Hanson rear bumper is a strong, supportive 60" wide bumper that can be expanded upon with a tire carrier and cargo racks, even at a later time if needs change. A 2" receiver is incorporated into all the Jeep rears, as are the welded-on clevis tabs as well. If you think you may want to use a tire carrier down the road, be sure to order the bumper with the spindle already mounted as it is a hassle to add later.
|
|
|
Hanson Offroad Rear Bumper in Black for 84-01 Jeep® Cherokee XJ
Jeep XJ Series Cherokee/Wagoneer ('84-'01) Rear Bumper. A 2" receiver is incorporated into the Jeep rear, as are the welded-on clevis tabs as well. The tabs are 1" thick.
|
$749
See 2 Stores
See All Stores
|
|
L-Brackets by Hanson Offroad
Available in a variety of configurations to suit your cargo carrying needs, Hanson Cargo Racks are constructed of 1” square tubing with .100” thick smooth aluminum flooring with strap attaching points under the lower frame tubes. Specifically designed to work with the Hanson Square Frame Tire/Cargo Carrier, predrilled holes are provided for many, but not every, cargo combination. Minor drilling may be required. Finished in durable black powder coat.
|
$158
See 2 Stores
See All Stores
|
|
1997-06 TJ Wrangler, Rubicon and Unlimited. Black powder coat. Made from heavy duty 3/16" hot rolled plate steel. 3/8" mounting plates and end caps. 2" receiver. Welded-on 1" clevis tabs with 7/8" hole. Equipped with a safety chain plate behind and under the receiver tube.
|
|
|
The combination of sturdy construction and multiple angles adds strength and optimizes departure angles. The unique placement and design of the 1 wide clevis tabs gives them unmatched strength allowing them to be pulled from any angle without fear of damage to bumper or tab, and do not interfere with departure and approach angles.
|
|
|
JK Rear Bumper with spindle mount tire carrier. Bumper is made of 3/16 steel, that is laser cut and formed. It has a drop down deck in it to allow the rear tire to be mounted lower. It has a built in 2" receiver. The tire carrier mounts to our spindle that has been in use for years with great success. The tire carrier, carries a 37" tire with no problems or rattles. It will carry a 48" HiLift as shown in the picture. Tire carrier opens very easily. It uses a bear claw latch very similar to a...
|
|
|
Why protect just the front of your SUV or CUV when lots of accidents happen from behind? The Black Horse rear bumper guard was created to provide better all-round protection for your SUV or CUV. It's also designed to fit without interfering with factory tow hitch packages. Available for most late-model SUVs and CUVs, the rear bumper guard bolts on in less than ten minutes. Available in double and single tube, the Black Horse rear bumper guard provides stylish protection and good looks. Easy...
|
|
(US)
