|
|
|
|
Cardi D2-220EL 15 Amp Motor 3-speed gearbox, ideal motor for up to 9" bits 15 Amp, 115 volt, 60 Hz, single phase On/off switch built-in Weighs 25 lbs Recommended Core Bit Diameters Low 490 Rpm bits 6" to 9" Med 830 Rpm bits 3" to 6" High 1,150 Rpm bits 1" to 3" 8230 Cardi D2-220EL 15 Amp Motor
|
|
|
MK Diamond Water Swivels Water swivel 1/2" shank to 5/8"-11 or water swivel 3/4"-16 Female Thread
|
|
|
Motor Spacer Spacer kit for Manta I, II and III core drill rigs with Milwaukee motors. Allows rigs to use 14" bits.
|
|
|
MK Diamond Shank Adapters Shank Adapters thread onto the core bit and provide easy attachment to most hand-drill chucks. 5/8"-11 male thread.
|
|
|
Shaft Couplings Shaft couplings permit positive thread-to-thread adaptation from machine to core bit. Male Female 5/8"-11 3/4"-16 3/4"-16 5/8"-11 1-1/4"-7 5/8"-11 5/8"-11 1-1/4"-7
|
|
|
MK Diamond Shaft Extensions Shaft Extensions easily attach to the core bit and allow for a deeper drilling capacity. Male 5/8"-11 to Female 5/8"-11, Length 12". Male 1-1/4"-7 to Female 1-1/4"-7, Length 12".
|
|
|
Core Bore M-1 Complete Anchor Rig Slide handle permits drilling in tight areas Small anchor base and carriage 2-1/2" square column with black oxidized finish 6" wheels for better mobility Complete Anchor Rig Includes:Anchor base, mast, carriage, control panel, ceiling jack, motor mount plate and your choice of drill motor: Core Bore, Milwaukee or Weka Complete M-1 Anchor Drill Rigs MODEL NO. MOTOR RPM SHIP WT. M1A-20-CB 20 Amp Core Bore CB748 350/900 125 M1A-20-MW4004 20 Amp Milwaukee...
|
|
|
MK Diamond Water Collection Rings Water collection rings sit snugly to ground allowing a wet vacuum to remove slurry. The small ring will accommodate bits up to 4-1/4". The large ring will accommodate bits up to 6".
|
|
|
Multiquip Cobra Dry Drilling Core Bit 10" Depth Cobra Dry bits are engineered to drill reinforced concrete with no water. Great for red brick, concrete pavers, retaining wall block and limestone stair treads. Run with low cost 1/2" drill or hand held core drill. 10" usable drilling depth. No water needed : eliminates the mess associated with drilling wet No expensive core rigs No long setup time : plug in your drill and go to work. save as long as 20 to 40 minutes per hole Interchangeable spring...
|
|
|
Weka DK32 3 Speed 30 Amp, 110 Volts, 230/480/720 Rpm Water attachment 1.250-7 threaded spindle
|
|
|
Kor-It 12" K-90-X System Complete anchor bolt drilling systems Free shipping Drill stand with anchor bolt base 3.5 hp electric motor with two speed gearbox-450/900 Rpm 20 hp hydraulic motor Up to a 12 in. diameter bit capacity Water swivel 22 in. carriage travel Bit capacities of up to 24-in. Power Sources – Electric, Pneumatic & Hydraulic K-90: 3.5 hp electric motor, 20 Amps, 115 Volt, 50/60 Hz. K-90-M2: 3.5 hp electric motor, 10 Amps, 220 Volt, 50/60 Hz. K-90-H: 21 to 48 Hp, hydraulic motor,...
|
|
|
MK Diamond Vacuum Pumps Oil-less operating 1/8 hp, 115 Volts vacuum pumps for Manta core rigs. Vacuum pump for Manta III combination core rigs. Vacuum pump with handle & iso-vibe foot pads, fits any combination drill stand.
|
|
|
DK 22S 23 Amp, 110 Volts motor.3 Speed 420/880/1300 Rpm Water attachment 1.250-7 threaded spindle
|
|
|
Kor-It 24" K-424 Gasoline Powered Core Drill Machines Free shipping Quick set-up - minimizes time required for each job Longer bit life with very stable drilling platform - reduces job costs Drill faster with gasoline power - get the job done in less time Stand-alone system requires no additional power - field independent Heavy-duty, dual-precision ground columns and tenzalloy precision machined carriage assembly Smooth-precision ball feed screw system Designed for large and small hole drilling ...
|
|
|
|
|
|
Milwaukee 4004 20 Amp Motor. Large selection of core drills, Big Savings
Milwaukee 4004 20 Amp Motor 115 Volt, 300-600 Rpm Built-in water swivel 1-1/4"-7 spindle thread Recommended bit diameters from 5" to 14" Weighs 40 lbs. Recommended bit diameters speed Low speed 300 idle Rpm bits 9" to 14" High speed 600 idle Rpm bits 5" to 8"
|
|
|
Milwaukee 4090 15 Amp Motor 115 Volt, 1 5Amps, 375-750 Rpm Built-in water swivel 1-1/4" - 7 spindle thread Recommended bit diameters from 2-1/2" to 8" Weighs 40 lbs. Recommended bit diameters speed Low 375 Rpm bits 5" to 8" High 750 Rpm bits 2-1/2" to 5"
|
|
(US)